How to Drain Your Water Heater: A Step-by-Step Guide

Tank water heaters are a dependable way to secure a fast supply of hot water for your home. The inclusion of a storage tank ensures some hot water is readily available. But over time, other substances may build up inside the storage tank. This may be sediment or mineral buildup arriving from the main water line or an opening in the pipes. Whatever the culprit is, this buildup will sometimes negatively impact the efficiency of water heaters. In severe cases it can plug up drainage and could even result in premature failure.

Fortunately, draining your water heater and removing sediment buildup is a relatively simple task. An experienced plumber in Naples can handle the process, but you can also drain the tank yourself if you know what you’re doing. Whatever you choose, draining the tank now can help lower the risk you’ll need premature water heater replacement.

Before You Begin…

Before you start draining the tank, you should shut off the cold water supply. The supply valve connects your water heater with the main water line. Unless you have access to a well (and you may need to drain the tank more regularly if you do), the water main delivers all the potable water your home uses. Keeping the valve shut will stop more water from flowing into the tank, allowing you to completely drain it.

You’ll also want to have a rubber hose, like one you could use for yard work. The hose allows you to safely drain the water heater tank without spilling water all over your garage, utility closet, attic or wherever the water heater is kept. Make sure you place the other end of the hose far away from your home to prevent the water from flooding back inside.

Finally, a screwdriver will help you loosen tight screws or valves. You shouldn’t need any more tools than this unless you stumble upon a problem with the water heater or adjacent piping. At that point, it might be best to hire a certified plumber in Naples.

Step 1: Shut Off the Water Heater

After you’ve cut off the water supply, you can shut off the water heater itself. This will be on the thermostat for natural gas water heaters or via a breaker switch for electric models. The pilot setting on gas water heaters can continue to stay on during flushing, but electric models need to be completely off. This is because of the heating elements electric water heaters have, which remain submerged. In a drained tank, they can quickly overheat. You should also review the model’s manual, as some water heaters need to be completely full before the heating elements are reactivated.

Even after you’ve shut off the water heater, you’ll need to wait for the water stored in the tank to cool down. It may be hours before the water cools to a safe temperature, so it is often best to leave the remaining steps for the following day.

Step 2: Attach the Hose to the Water Heater’s Drain Valve

Tank water heaters possess a drain valve you can use to empty the storage tank. Once you’re certain the water supply is disconnected and the water heater itself is off, locate the drain valve. Some models may have it covered up. Make sure the hose is firmly attached to prevent spilling hot water near you and the water heater.

Step 3: Open a Faucet or Other Hot Water Tap

Your home’s plumbing uses pressure within the piping to deliver a consistent flow of water from the main water line to the rest of the house. This pressure will have to be relieved before the hot water can actually flow from the tank. By heading to the nearest faucet or spigot, you’ll release the pressure inside the piping. All you have to do is open the hot water tap to relieve the pressure before heading back to the water heater.

Step 4: Release the Drain Valve

Remember that this water could still have some residual heat. Open the drain valve and allow all the water to drain from the tank. This should pull sediment buildup out of the tank and away from your home. But some buildup might be stuck to the inside of the tank. Turning the cold water supply back on will help wash away stubborn minerals and other substances from the tank.

Keep repeating this step until the water looks free of sediment or minerals. If the drain isn’t working because of an obstruction, a trained plumber is likely required.

Step 5: Re-Shut the Valve Before Refilling the Water Heater

If everything proceeds normally, you should be able to remove most excess sediment stuck inside your water heater. Retighten the drain valve, disconnect the hose and open the water supply to get things working again. As the water heater tank begins to fill, return to the hot water tap you opened. Once cold water starts to flow, you know the pressure is back where it needs to be.

At this point, you can open the gas valve or flip the breaker switch back on. Like we mentioned earlier, don’t forget that certain models might need to be entirely full before the water can be safely heated. Make sure you check your manufacturer’s instructions before starting the process.

Keep Your Water Heater Sediment-Free for Best Results

Tank water heaters are still a great option for supplying your hot water needs. Draining the tank every 1-2 years will help flush sediment buildup and keep things running at peak efficiency. If you think your water heater is past the point of efficient heating, consider looking for water heater replacement in Naples from a technician you trust.

 

chat now widget box